Cerec 3D CAD CAM Dentistry in Cincinnati, Ohio

13 Responses to Cerec 3D CAD CAM Dentistry in Cincinnati, Ohio

1. spinceara says:

   January 18, 2012 at 10:20 pm

   interesting)

   Reply
2. sexykatie90 says:

   January 18, 2012 at 10:48 pm

   nice add me as a friend k

   Reply
3. DocCrutch says:

   January 18, 2012 at 11:27 pm

   If you really want to have great teeth and have a greater ability to chew and actually enjoy food, I would suggest looking at having implants placed to support a new denture set. Admittedly, it isn’t cheap. It can, however, add very many years to your life as your nutritional needs will be met more adequately. Money is only paper and you can’t take it with you. Get the implants.

   Reply
4. DocCrutch says:

   January 18, 2012 at 11:36 pm

   @harleypiper / Typically, the average person has 175 lbs per square inch in bite force to chew food. When you replace an entire arch of teeth with say, a denture plate, that total force drops to between 75-100 lbs. With a complete upper and lower denture set, you’re in the ballpark now of 35 lbs per square inch. Transmission of bite forces and loading is significantly reduced, and you will encounter over time resorption of the bone that once supported the teeth and make up the mid-face.

   Reply
5. noorseo88 says:

   January 18, 2012 at 11:56 pm

   CAD ZONE is a CAD / CAM / CAE / MANAGEMENT software training and solution provider.
   CAD ZONE is established to provide software training &services in the field of Mechanical, Architecture,
   Civil, Interior and? Project Management. CAD ZONEis backed by high profile and experienced manpower
   to provide software training and project outsourcing.
   (cadzone. org)

   Reply
6. harleypiper says:

   January 19, 2012 at 12:22 am

   I sure would benefit from that.
   I was assaulted back in 1988 while walking home at night from work.
   they hit my face enough times that I wear uppers and lowers. I was only 27
   I miss eating the same foods as the rest of the family. I’m always depressed inside about the way I look . I doubt that I’ll ever have the delight of throwing away the ole fixdent tube. I would rather have great teeth again then to be famous.

   Reply
7. HerbBeamish says:

   January 19, 2012 at 12:45 am

   P T BARNUM WAS RIGHT!!!!!!!!

   Reply
8. EPLCeramics says:

   January 19, 2012 at 1:30 am

   I have a furnace that can sinter a crown in less than half and hour and only costs $6,999. 00 U. S.

   A conventional furnace will take 6 hours or more to sinter the crown

   Reply
9. prismdentalceramics says:

   January 19, 2012 at 1:48 am

   convenience is higher, but quality is lower. margins and glaze are poor

   Reply
10. Liquidguitars says:

    January 19, 2012 at 2:30 am

    If your dentist does not have one, your at the wrong dentist. . no joke.

    Reply
11. MestizoFilipino says:

    January 19, 2012 at 2:41 am

    Now that’s cool. 

    Reply
12. ttudad says:

    January 19, 2012 at 3:06 am

    If you’re a dentist and haven’t even looked at this product don’t miss the boat. It’s conservative, cost effective and is best for the patient. Open your mind! There are too many using this for it not to work. If however you are a marginally talented dentist your work will still suck. It’s a computer- garbage in garbage out. Give it a look.

    Reply
13. 0Tanja0 says:

    January 19, 2012 at 3:50 am

    1000 dollar? where? in US? in Russia Cerec is 200-300 dollar, and Cerec crown is 500 with Zirconium

    Reply